數據參數
DATA PARAMETERS
內徑表面拋光等級 Inside Diameter Surface Finish Level
不同的內部表面拋光技術獲得不同等級的鋼管。
Tubes & Pipes are available with different inside diameter finish levels.
 |
 |
 |
 |
|||||||
AP |
酸洗鈍化管 Annealed and Pickled |
MP |
機械拋光管 Mechanically Polished |
BA |
光亮退火管 Bright Annedled |
EP |
EP管 Electro Polished |
|||
| 區分 Inside Surface Level | 外徑尺寸 O.D.size | Ra(μinch) | Ry(μm) |
| AP | 所有 ALL | ≤100 | ≤25 |
| MP | 139.8≤OD≤355.6 | ≤20 | ≤4.0 |
| BA | 6.35≤OD≤48.6 | ≤15 | ≤3.0 |
| 48.6≤OD≤165.2 | ≤20 | ≤4.0 | |
| EP | 6.35≤OD≤48.6 | ≤10 | ≤0.5 |
| 48.6≤OD≤165.2 | ≤10 | ≤0.7 |
化學成分表 Chemical Composition
| 鋼種 Steel Grade | C | Si | Mn | P | S | Ni | Cr | Mo |
| 304SS | ≤0.080 | ≤1.000 | ≤2.000 | ≤0.040 | ≤0.030 | 8-11 | 18-20 | - |
| 316/316L Dual | ≤0.035 | ≤0.750 | ≤2.000 | ≤0.040 | ≤0.030 | 10-15 | 16-18 | 2-3 |
| 316L SIMGLE | ≤0.030 | ≤1.000 | ≤2.000 | ≤0.040 | ≤0.030 | 12-16 | 16-18 | 2-3 |
| 316L DOUBLE | ≤0.010 | ≤0.300 | ≤0.400 | ≤0.040 | ≤0.030 | 14-15 | 16-17 | 2.2-2.5 |
物理性能 Physical Prorerties
| 鋼種 Steel Grade | 屈服強度 Yield Strength（N/mm2） | 拉伸強度 Tensile Strength（N/mm2） | 伸長率 Elongation（%） |
| 304SS | ≥205 | ≥520 | ≥35 |
| 316SS | ≥205 | ≥520 | ≥35 |
| 316LSS | ≥175 | ≥480 | ≥35 |
粒子供給實驗 Particle Contribution Test
| 區分 Inside Surface Level | 標準 Standard | |
| 最大粒子直徑 Max Particle Size | 允許粒子數量 Allowabel Particle No | |
| AP | ＞0.3μm | 5/cf |
| MP | ＞0.1μm | 5/cf |
| BA | ＞0.1μm | 5/cf |
| EP | ＞0.1μm | 1/cf |
品質檢驗項目及標準 Quality Sssurance Values
| 檢測項目 Inspection Items |
油脂成分測試 Oil Content Measurement |
純水阻抗測試 Liquid Registivity Measurement |
離子分析 Ion Charomatography Analysis |
露點測試 Dew Point Measurement |
| AP | 0.1mg/ft2或最低（or lowest） | - | - | - |
| BA/MP | 0.01mg/ft2或最低（or lowest） | ≥18MΩ?cm | 10ng/cm3或最低（or lower） | -75℃或最低（or lower） |
| EP | - | ≥18MΩ?cm | 5ng/cm3或最低（or lower） | -75℃或最低（or lower） |
尺寸公差 Dimension Tolerance
| 外徑 Outside Diameter | 壁厚 Wall Thickness | ||||||||||||||
| Tube | Pipe | MP/BA/EP | AP | Tube(mm) | Pipe 管表號5S Pipe Schedule 5S |
Pipe 管表號10S Pipe Schedule 10S |
|||||||||
| 英寸 Inch |
米制 Metric |
A | 英寸 Inch |
T | MP/EP | BA | AP | T | MP/BA/EP | BA | T | MP/BA/EP | BA | ||
| 1/4 | +0.1 -0.00 |
±0.30 | 1.00 | +0.05 -0.00 |
+0.05 -0.00 |
±0.30 | |||||||||
| 3/8 | 1.00 | ||||||||||||||
| 1/2 | 1.24 | +0.01 -0.15 |
±0.1 | ||||||||||||
| 3/4 | 1.65 | ||||||||||||||
| 1 | ±0.1 | 1.65 | |||||||||||||
| 6 | +0.1 -0.00 |
1.00 | +0.05 -0.00 |
+0.05 -0.00 |
|||||||||||
| 10 | 1.00 | ||||||||||||||
| 12 | 1.00 | +0.01 -0.15 |
±0.1 | ||||||||||||
| 19 | 1.50 | ||||||||||||||
| 23 | ±0.1 | 1.50 | |||||||||||||
| 8A | 1/4 | ±0.08 | ±10% | 1.20 | ±0.12 | ±0.20 | 1.65 | ±0.15 | ±0.20 | ||||||
| 10A | 3/8 | ±0.10 | 1.20 | 1.65 | |||||||||||
| 15A | 1/2 | 1.65 | ±0.15 | 2.10 | ±0.21 | ±10% | |||||||||
| 20A | 3/4 | 1.65 | 2.10 | ||||||||||||
| 25A | 1 | 1.65 | 2.80 | ±0.28 | |||||||||||
| 32A | 1-1/4 | ±0.15 | 1.65 | 2.80 | |||||||||||
| 40A | 1-1/2 | ±0.20 | 1.65 | 2.80 | |||||||||||
| 50A | 2 | ±0.40 | 1.65 | 2.80 | |||||||||||
| 65A | 2-1/2 | 2.10 | ±0.20 | ±10% | 3.00 | ±0.30 | |||||||||
| 80A | 3 | 2.10 | 3.00 | ||||||||||||
| 100A | 4 | ±0.80 | 2.10 | 3.00 | |||||||||||
| 125A | 5 | ±1.00 | 2.10 | ±0.28 | 3.40 | ±0.34 | |||||||||
| 150A | 6 | ±1.50 | 2.10 | 3.40 | |||||||||||
| 200A | 8 | ±2.00 | 2.10 | 4.00 | ±0.40 | ||||||||||
不銹鋼氣缸管 Pneumatic Cylinder Stainless Steel Tube
| 不銹鋼氣缸管 Pneumatic Cylinder Stainless Steel Tube | |||||||
| 內徑 Internal Diameter(mm) | 外徑 Outside Diameter(mm) | 壁厚 Wall Thickness(mm) | 圓度 Roundness | 直線度 Straightness | 粗糙度 Roughness | ||
| 6 | +0.04 0 |
7 | +0.04 -0.04 |
0.5 | 0.03 | 1.5mm/m | Ra≤0.4μm |
| 8 | 9 | 0.5 | |||||
| 10 | 11 | 0.5 | 1.2mm/m | ||||
| 11.25 | 0.63 | ||||||
| 12 | +0.05 0 |
13.4 | +0.05 -0.05 |
0.7 | |||
| 15 | 16.6 | 0.8 | 1mm/m | ||||
| 16 | 17.4 | 0.7 | |||||
| 18 | 1 | ||||||
| 20 | 21.4 | 0.7 | 0.04 | ||||
| 22.8 | 1.4 | ||||||
| 25 | 26.4 | 0.7 | |||||
| 27.8 | 1.4 | ||||||
| 32 | +0.06 0 |
33.6 | 0.8 | 0.05 | |||
| 35 | 1.5 | ||||||
| 40 | 41.6 | 0.8 | |||||
| 43 | 1.5 | ||||||
| 50 | +0.07 0 |
52 | +0.07 -0.07 |
1 | |||
| 53 | 1.5 | ||||||
| 63 | 65 | 1 | |||||
| 66 | 1.5 | ||||||